Ad810 Frequency Inverter Pm Motor Drive Variable Frequency Converter

• Customization: Available
• Application: High-performance Transducer, Three Phase Transducer, General Transducer, Single-phase Transducer, High Frequency Converter Transducer
• Output Type: Dual
• Model NO.: AD810
• Principle of Work: V/F Control ,Vecter Control
• Switch Mode: PWM Control
• Main Circuit Type: Current
• Voltage of Power Supply: Low Voltage Variable-Frequency Drive
• Link of Transformation: AC-DC-AC Variable-Frequency Drive
• Nature of DC Power: Voltage Variable-Frequency Drive
• Function: Simple Type, Elevator Special, Textile Special, Constant Torque Universal Type, V/F Control ,Vector Control
• Transport Package: Carton
• Trademark: ABC
• Origin: China
• HS Code: 8504

Product Description

Product Description

AD810 High Speed PM Motor Drive
AD810 is suitable for the control of magnetic suspension and air suspension bearing PM motor with the characteristics of high frequency, high speed and high power density

Product Features

1, With control algorithm for Ultra-high speed  PM motor, it is especiallysuitable for the control of permanent magnet synchronous motor with magnetic bearing or air bearing.

2, With the optimized Hybrid PWM control, the  harmonics of motor current are smaller at the same swtiching frequency.

3, Motor frequency up to 1600Hz with perfect sinusoidal waveforms of motor current.

4, Support output Sine-filter control with auto compensation for amplitude attenuation and phase offset caused by sine-filter connected between the frequencyconvertor and motor.

5, High power density, latest power electronic technology and heat pipe technology etc. are used.

6, KEB function
When there is a failure in the customes power grid, AD810 can keep the DC voltae with the kEB function and supply power to the customer's control system so that the whole system can be controlled safely until the motor is controlled to a speed lower than the safe limit

Project		Specification
Line in	Voltage	3-phase 380~480V - 15 %~+10%;
	Frequency	50/60Hz ± 5%
	Maximum unbalance	3%;
Output	Voltage	3-phase 0 ~100% input voltage;
	Frequency	0 ~ 1600Hz ;
Main Control	Control mode	V/F, Vector control;
	Supported motor type	IM / PM
	Starting torque	0.5Hz 150%;
	Overload	Heavy load type : 150% ~ 60s  ; 180% ~ 3s
	Switeching frequency	2k~16kHz;
	Speed resolution	Digital: 0.001Hz,  Analog: 0.5‰ of the maximum setup;
	Speed accuracy at speed Open loop	±0.5% rated;
	Source control command	Keyboard, Dlinputs, Bus communication;
	Set frequency source	Keyboard, analoge, pulse inputs Bus communication;

	Acc / Dec		4 groups paraineter for acc/dec: 0.05-6000.00s ;
Project	Specification
Basic functions	Speed open loop, speed closed loop, process closed loop control , torque open loop, torque closed loop , motor auto tuning, motor pre-excitation, automatic load compensation, automatic voltage regulation, acceleration and deceleration curve control, DC brake, AC brake, speed limit, torque limit, current limit, flying car start, instant stop, automatic reset, hybrid modulation function, LC filter compensation function, etc. ( Note : Speed close loop or torque control with speed sensor will active only when a control unit and PG card are installed )
Application function	Multistage speed control by terminals or PLC function, Sramp, mechanical brake, counter, process PID , jog etc.
Protective function	Short circuit, ground fault, line phase loss, under voltage, over current, overload, over temperature, motor thenmal protection, motor phase loss, control wire broken etc.
control terminal	30-500 kW _	DI input terminal	5 Dis for NPN and voltage input;
		DO output terminal	1 Dis for OC gate open output;
		RS485 communication terminal	1 RS485 / Modbus, maximum 38400bit/s;

		AI output terminal	2 AI of voltage and current input;
		AO output terminal	2 AO of Current and voltage output;
		Operation keyboard	built-in
Operation environment	Protection Lervel		IP20;
	Workting temperature		Operating range -10 °C~60°C Nominal current to 40°C, derate form 40 ℃;
	Working humidity		5%-85% (no condensation at 95%);
	Vibration		1.14g
	Altitude		1000m, derate from 1000m;
	Motor cable length		Shielded cable: 50m; Unshielded cable: 100m;

Main Product

Company Profile

Jiangxi ABC Electric Co., Ltd. is a high-tech enterprise based on power electronics, automatic control and Internet of things technology, focusing on the research and development, production and sales of industrial automation control products. Founded in 2018, ABC is headquartered in Jinggangshan Economic and technological Development Zone, a national development zone, with R & D facilities in Beijing and Shanghai. ABC focuses on automation, digitization and intelligence in the industrial field, devotes itself to the continuous innovation of industrial technology, being close to customer needs, serving customer growth and value enhancement, and providing customers with high-performance products and personalized solutions which are more intelligent, more reliable and more open.

Certifications & Exhibition & Packaging & Shipping

FAQ

Q 1: Are you trading company or manufacturer?
A1: We are manufacturer.
Q2. What is your supply capacity?
A2:200,000PCS/year.
Q3: What is the standard of package?
A3: Carton box or plywood case.
Q4: What's your warranty term?
A4: We offer 18 months warranty time.
Q5: Can the inverter connect with computer?
A5: Yes. All inverters have built-in RS485communication